How to fix pull up shower diverter

How to fix pull up shower diverter. Checking the valve for starters might help you in fixing your pull-up shower diverter. Other things that are obliging are presented as well.

You want hot water, and cold water is coming from the faucet or showerhead. It can be the inverse of this. That is a problem you do not want in extreme weather. It may be that the diverter broke or the supply to it was dislocated.

You need to control the valve to fix it. The supply should be restored. The spout is too dirty and cleaning it can make it viable again. The broken knob should be prepared in any case.

How to fix pull up shower diverter

fix pull up shower diverter

Cut or thoroughly remove any water supply. With tape and threads, seal the pipes and the small screws that are attached to them. Do not let them drain away. Put them on the safe side.

Unscrew all and store them safely. Then loosen the diverter. Pull it off and wiggle it while doing so. Now get the new diverter in its place.

Fix it there. Tighten it, but with mediocre force. Refrain, so you do not cause any damage to it.

Useful ways for you are gathered here. Gain knowledge and learn by checking them out.

Mineral removal by vinegar

Most areas have hard water. Because of this reason, the minerals in hard water move through the appliances and pipes. The minerals, like lime, get attached to each other and form a wall.

This interrupts the smooth flow. And doesn’t let the diverter function as it restricts water movement. The knob becomes immovable.

Vinegar can be used against it and aid in the eradication. The effects skyrockets when used with baking soda. So you just need to pour some amount into a plastic bag. Then dunk the diverter in it. After immersing, set the plastic bag there using tape.

Let it stay immersed like that for at least 12 hours. Then try turning the knob. It will move quite easily and water pressure will be suitable too. Pass hot water through it to clear loose minerals.

Lubricating stuck parts

Sometimes the reason is not enormous. The diverter is just stuck and is not moving. Though the reason is not enormous, annoyance is. Rust is likely to build up in the presence of moisture. And moisture because the water is present in it or passes through it.

Corrosion starts slowly, but at a time, the thick layer renders it immovable. And without moving it, you can not run the water. It may not be stuck, but toughness can be annoying.

So we use lubricants and other chemicals that are effective against rust. WD-40 is common, but it is not necessary to use this one.

Water and lubricants don’t go well together, so dry them beforehand. Use a towel or a dry cloth to do this. Now directly apply it to the required area, like the knob.

You can spray it from the bottle. Spray the tub spout with aid of a straw. Move the knob as you spray to restore it to working back. Let it stay half an hour if it is too stuck. Do this again and again until you are sure about the smooth movement.

Complete replacement

complete replacement

The above methods might work, but you may still not be satisfied with them. This is because the problems can come back again. It may seem that your diverter is not working.

To be honest, the replacement is better than trying to fix the old one. It will give you peace for a long time. But be sure to take care of the new one. This will give it a long life.

Match the new one with the old one. Or get a similar one, like if the old was threaded, then the new one should be too. Check the old length, meaning the length of the old spout. Make sure to but the exact size.

Clean the line if it is threaded or taped. Apply a new layer on both the pipes and use a wrench to tighten it up. Allen screw spout will come off by sliding easily. Put the new diverter and then try it.


Fixing it is not difficult, but you should check everything precisely. The wrong installation or method of repairing will not end well for you.

You may need a professional if you are not accustomed to this work.

Related Guides