Dyson v6 flashing red light. Vacuum cleaners are now a necessity in every house, and almost all families rely on them for cleaning. Right?
Dyson’s world-famous company has launched this tremendous wireless vacuum with HEPA filters that capture minute particles and allergens.
This amazing machine is not only cordless, but it’s also an all-in-one machine that can transform into a hand-held device for easy cleaning of small and difficult places.
It can even transform into a long tube vacuum for cleaning ceilings and higher classes. But there are sometimes when your electrical devices let you invest and look into them to detect the actual culprit.
This is usually caused by a low-voltage 18650 lithium-ion cell. It’s tough to open this battery. I’ve seen a few people open them to replace a single 18650 cell on the internet, but you’ll have to hack the case.
It is far more convenient to purchase a high-quality Dyson battery for the V6.
If your Dyson v6 flashes a red light when charging, there might be something that it tries to indicate.
The battery is fully charged when there is no light on. A flashing red light characterizes a fault—Dial Dysons’ toll-free number.
A flaw is indicated by a flashing red and blue light. If the problem persists despite all of the fixes, you can contact Dyson for assistance.
Dyson v6 flashing red light (Troubleshoot)
The main issue that comes with almost every wireless vacuum is the flashing of red lights.
There is a problem with the machine, and it gives a warning. Either there could be an issue with the battery or the main body.
Following the best possible troubleshooting might help you eliminate the problem or minimize the effect.
Removing the motorhead might help
To begin, remove the motorhead and inspect it for any faulty wires or stuck rotating brushes. If this doesn’t fix the problem, move on to the next step.
Under voltage fault
Both sides of the battery have flashing red lights. If they flash, one or more of the battery cells have an Undervoltage fault. The only solution is to replace the old battery with a new high-capacity one.
Refasten the padlock
Carbon fiber is used to make the brush strip. This tool includes a bracket. This lock is identified by a padlock that you can unlock after a period and intensive use.
You only need to replace the padlock and secure it with a small coin. Before vacuuming again, double-check that it is properly seated.
Clean the brush bar
For the Dyson v6 to work at its best, it needs to be appropriately maintained. This means you’ll have to clean the parts regularly.
The brush will stop working correctly if it becomes clogged with dirt and dust over time.
When the encounter becomes worn out, you can clean it or replace it entirely.
In any case, simply cleaning the brush will restore your vacuum cleaner’s functionality.
Replacing the battery pack
If the above steps don’t work, the battery is the next place to look. A lithium-ion battery powers the Dyson v6. It may be time to replace the battery in your vacuum cleaner, depending on how long you’ve had it.
Follow the following to return the battery pack.
- Begin by removing and emptying the garbage can. The less strewn about, the better. Loosen the two 2-star screws in the handle’s bottom and top.
- The battery may be stiff depending on how long it has been since you purchased the vacuum cleaner. The dust buildup in the handle is the cause of the stiffness.
- Only use a battery that is the same size and type as the one in the vacuum cleaner to replace the Dyson v6 battery. Slide to the right and lightly tap while sitting, and it should look almost the same.
Dyson V6 flashing red light 10 times
If you observe that your vacuum flashing red light, you may have to sit for a while, hold the trigger and count the number of times your machine flashes; if the Dyson V6 is flashing red light 10 times or less than 10 times, then there is a high possibility of a problem in the main body.
There could be a part not working properly, or maybe there could be some major problem inside the motor that requires replacement of the motor.
To find out what’s wrong with the system, try reaching out to the support representatives of the company for further assessment of the machine.
Dyson V6 flashing red light 32 times
If your Dyson V6 is flashing red light more than 10 times, then most likely there is an issue with the battery. A flashing red light always indicates a problem with the machine, and that requires an immediate checkup.
If the Dyson V6 is flashing red light 32 times, then that means there is surely some issue with the battery.
There could be a failure in the battery pack, or the battery may get weak due to excessive usage.
The solution to this problem could be either you fix the battery or you replace it with a new one; the battery pack could only be fixed if you open up the system and replace the 1850 cells, which of course, is pretty hard to do.
The easier and better way of fixing your battery problem is to completely replace the battery with a new one.
The replacement of the battery would help your vacuum to be good as new with stronger suction power and excellent performance.
How do you replace the battery of a Dyson V6?
The right way of replacing the battery is to first remove the rubbish canister where all the rubbish is stored from vacuuming.
After removal, you will need to unscrew the 2-star screws from the top of the handle and the lower end of the handle; once your screws are unscrewed, you will see the battery in front of you.
Take the battery out to replace it with a new but identical battery. Make sure the new battery sits right in place, then put the screws back in their designated places.
There you have your Dyson V6 with no red flashing anymore.
We hope this article focusing on flashing red lights 32 times or 10 times helped you resolve the issue.
So, if you were planning to throw your device due to the case, you should change your mind because you just need to replace the battery, nothing else.
Make sure you have your hands on the correct battery for your device. You can fix the battery by yourself; no expert help is required for the replacement.