Black And Decker Dustbuster Troubleshooting

Black And Decker Dustbuster Troubleshooting. Some places can not be reached by the simple vacuum cleaners we use. This is because the area is too small or the place is out of reach.

This is where Black and decker dustbusters come in. They are actually handheld vacuum cleaners.

They are easy to use and are very reliable. They can be used in tiny clogged spaces where we were unable to reach before.

Certain problems that are related to handheld vacuum cleaners also occur in these devices. Though these devices are of good quality, they are not issue proof either.

They can also have power issues arising in them or it can be related to any other part that was not maintained.

Black And Decker Dustbuster Troubleshooting

black and decker dustbuster troubleshooting

The handheld vacuum cleaners can be clogged. They might be weak to suck in any debris. It is possible that the motor isn’t working as it should. The batteries might have gone dead.

The charging port could have been damaged, so the device is unable to charger itself. There can be other reason like the vacuum might not even power on when we need it to function.

Troubleshooting can be helpful in such cases as we will know what we are dealing with.

Batteries being dead

The first issue that is most common with the devices that run on batteries is the batteries being dead.

This might not seem that much of a big deal, but if your batteries are dead, you won’t be able to use your device even if you want to. The fix, on the other hand, is simple.

Steps to solve

  • Remove the screws on your device.
  • Take out the old batteries.
  • Take them to the market and buy the batteries that resemble and match them.
  • Place the batteries inside the cleaner and make sure they are placed in a correct position.
  • Turn your device on to see if it’s working.


No power in such devices is usually related to the batteries, so make sure to check them before you think of the problem too deeply.

Broken button

All electronic devices have a power button that helps the user turn the device on or off. The button is important, as the device will not turn on or off without it.

The button is also for safety as sometimes you might need to turn off the device because of some problem. This button might get damaged or break. This will annoying for us. So we fix it to work.

  • Open the screws of the device using a screwdriver.
  • Like above, remove the batteries so that the device doesn’t misbehave.
  • Unscrew the switch.
  • Remove the wires that are attached to the switch.
  • Lossen the screws and the worse will come out.
  • Lift the switch and take it out carefully.
  • Check if the switch is broken or just damaged.

If it’s damaged, try fixing it. You might be able to do so.If the switch is broken, you need to install a new one.

  • Connect the wires to it and tighten the screws.
  • Place it back inside and tighten the screws.
  • Place the batteries back and close the device.
  • Check to make sure the switch works.

Clogged filter

clogged filter

Clogged filter is pretty common in devices that filter and deal with stuff like water and air. As the vacuum cleaner, be it simple of handheld ones need to suck, filters are installed so the dirt or dust does to invade the machinery of the motor.

The filters getting clogged is not an enormous problem but it can cause disfunction i your device so cleaning and maintaining them is a pretty good idea.

  • Open the advice like before.
  • Remove the batteries as well.
  • Unscrew the filter carefully s it might get damaged.
  • Take the filter out by lifting it with your fingers.
  • Use a brush and water to clean the filter.
  • Clean the device from inside as well.
  • Install the filter back to its original position.
  • Then close the whole device.
  • Power your device on and see if it is working.


The ways to deal with problems that are associated with handheld vacuums are pretty simple. You just need to be careful not to damage anything further.

Other problems can also be found, ut they are a little advanced, so read the manual or get help to fix them.

Related Guides