Maytag washer won’t agitate but will spin

Maytag washer won’t agitate but will spin. The washing machine has several working components that seamlessly work to make your washing day a little easier.

Throughout the washing cycle, if you realize that the washing machine is spinning rather than stirring, it can be inconvenient.

If the washing machine spins instead of stirring, some partial obstacles can lead to this dilemma.

You might be able to tackle the issue yourself if you’re willing to wade into the troubleshooting waters.

Why Maytag washer won’t agitate but will spinwhy maytag washer won't agitate but will spin

If the washing machine turns without stirring, check the following common mistakes and unplug the washing machine.

  • Broken Agitator
  • Transmission Failure
  • Time Failure
  • Defective Lid Switch
  • Faulty Drive Motor

Transmission Failure

In a top-load washer, the transmission is responsible for turning the motor’s spinning motion into the agitator’s back-and-forth action.

The information has an input shaft that is driven directly or via a belt by the motor, as well as an output shaft that goes to the agitator. 

Transmission breakdown is yet another explanation for why the washer does not agitate but spins—the connection aids in the back-and-forth movement of the agitator.

Solution for this

Inspect the agitator’s input shaft. The transmission may need to be repaired if the input shaft turns, but the agitator does not.

Broken Agitatorbroken agitator

The agitator in top-loading washing machines is essential for moving the clothes through the water and detergent and is driven by the driveline output shaft.

To achieve a tight fit, the output shaft is generally splined, and the center of the plastic agitator has a matching spline.

If the washing machine spins without stirring, it may be due to a defective mixer.

The agitator is the heart of a top-load washing machine that moves and moves laundry through the water during the washing cycle.

The gearbox output shaft is splined to the agitator and held in place. Over time, under regular use, some stirrer components may wear or break, causing the washing machine to stop moving.

Solution For This

If nothing else seems to be in working order, the problem should be resolved by replacing the agitator.

Defective Lid Switchdefective lid switch

The lid switch is one item that is frequently neglected in this situation. When you shut the lid on a top loader, the lid switch starts the wash cycle.

The lid switch engages when you close the lid, signaling the washer to agitate during the wash cycle.

Solution for this

Use a multimeter to check the lid switch for continuity. However, if there is a connection, you must investigate the rest of the motor circuit, including the timer and selection switch. A word of caution: the untrained eye may struggle with this.

Time Failure

The timer, lid switch, water level switch, and selector switch are all used to regulate the drive motor. The timer’s job is to provide the right amount of power to switch the engine on in the right direction.

The timer is one of the elements that control the drive motor, which is connected to the agitator via an indirect connection. The timer allows the engine to turn on and move properly by supplying power.

Solution for this

Turn off the washer’s power supply. To test for continuity of the timer contacts, utilize a wiring diagram and a multimeter. The timer must be replaced if there is no consistency.

Faulty Drive Motorfaulty drive motor

When the washer doesn’t agitate yet spins, it’s possible that a malfunctioning drive motor is to blame.

The motor drives the gearbox, which oscillates the agitator. A technician should diagnose a faulty drive motor because it is challenging.

Solution For This

If you suspect drive motor failure, get a technician to diagnose and repair your washer.

Conclusion

We’ve covered everything you need to know about the Maytag washer won’t agitate but will spin in this article. A faulty agitator could cause if your washer didn’t agitate yet spins.

To keep the agitator in position, the transmission’s output shaft is splined to it. Some of the agitator’s components can wear out or break with typical use, resulting in your washing machine not agitating.

Related Guides