How To Tell If Washer Suspension Rods Are Bad

How To Tell If Washer Suspension Rods Are Bad. Washing machines are technological miracles that can get quite complicated, all while efficiently and effectively getting clothes clean.

It is easier to do the wash when there are several interior components and we must replace the bad component before we can use the washer again.

If your washer suspension rods are bad, your washing machine will likely vibrate while it’s in use. Reduce vibration and shaking by removing and replacing the inefficient suspension rods.

Also, to have access to the suspension rods, simply remove the panel.

How To Tell If Washer Suspension Rods Are Badhow to tell if washer suspension rods are bad 2021

Check for tremors or vibrations

Remember that a small amount of vibration is perfectly natural but when you start to detect significant shaking or vibrating coming from your washing machine, it’s time to be alarmed that a component has been damaged or broken.

Examine the Suspension Rods

It’s essential to inspect the suspension rods if you notice shaking or vibrating. They’re usually found beneath the drum, within the cabinet.

Visually inspect them first, looking for apparent signs of damage and wear and tear. If you discover a broken suspension rod, the only solution is to replace it.

How to Fix or Replace the Suspension Rodhow to fix or replace the suspension rod

In many ways, the suspension rod is quite similar to the suspension on your car. The majority of laundry washers use suspension rods that are arranged in four groups.

They are designed to provide cushioning for the internal drum during the fast motion of the spinning cycle.

The continual stress of a regular washing cycle might cause the rods to stretch and break. Visually, the washer’s drum seems out of balance which shows a broken rod.

Tilt the Washer

Pull the washer away from the wall to begin. Because the suspension rod is placed within the cabinet, you’ll need some extra space to work.

Disable the Power

Make sure the washing machine is turned off and unplugged from the outlet. Working with live electricity is extremely risky, and there is a risk of electrocution because there is water trapped in the washing machine.

Remove the Front Panelremove the front panel

The next step is to remove the front panel nuts and a Phillips screwdriver is typically required. Washing machine panels tend to be situated at the front of the machine.

If you can’t reach the screws, be careful to hold up the front of the panel (such as using wood blocks) to keep it stable.

Separate the Panel

Slide the panel in your direction by pushing it up as you go, with the screws removed. The top of the panel should now be separated from the rest of the main washer unit.

You don’t want to break any parts of the system by pulling too hard. For the time being, set the panel to the side.

Detach the Top Panel

It’s time to move on to the upper panel now that the front panel has been removed. Remove the screws on the upper panel using your screwdriver. You should be able to discover them directly under the washer’s lid or in the cabinet’s corners.

Lift the rod out by releasing the tension

Lift up the interior tub near the aforementioned rod that you know where the failing tension rod is. Carefully remove the pressure from the damaged rod with one hand.

Putting in the New Rod

Replace the new rod on the upper opening after removing the old one. Make sure you have a firm grip on the rod so the top assembly sits just above the aperture.

While holding the rod, back into the opening of the fastening cup so it encompasses the entire length of the rod and checks the cup fits tightly in the opening.

Return the Panels and Connect the New Rod

Using one hand, unscrew the internal tub of the washer from the underside. Insert the bottom part of the rod into the u-shaped connecting point while holding it with your other hand, then remove the tub carefully.

To keep the tub in place, the new rod should function in combination with the other three rods. You can place the panels back on the front and top and make sure the new rod is secure.

Conclusionreturn the panels and connect the new rod

In this article, we discussed how to tell if washer suspension rods are bad? Well, when it comes to indicating a bad washer suspension rod, the largest sign is that your washer is vibrating or shaking more than usual.

If you really want to know, open the washing machine cabinet and have access to the washer suspension rods for checking any damage.

Don’t neglect to remember that other factors can contribute to your washer vibrating, including the rods. It’s also possible that numerous broken parts on your machine are creating the problem.

Before starting troubleshooting, you should ensure your machine’s surface is equal and that your loads are even.

We hope this article is beneficial for you!

How To Tell If Washer Suspension Rods Are Bad

Related Guides

Leave a Comment